[Free] 2018(May) EnsurePass Examcollection Microsoft 74-697 Dumps with VCE and PDF 31-40

Ensurepass.com : Ensure you pass the IT Exams
2018 May Microsoft Official New Released 74-697
100% Free Download! 100% Pass Guaranteed!

OEM Preinstallation

Question No: 31

You have a Windows Recovery Environment (Windows RE) image named Winre.wim. You need to enable support for HTML applications in the image.

Which tool should you use?

  1. Winrecfg

  2. Reagentc

  3. Sysprep

  4. Dtsm

Answer: A

Question No: 32

You have a Windows 8 image.

You are testing the Out-of-Box-Experience (OOBE).

You discover that when neither a keyboard nor a mouse is connected, the Human Interface Device (HID) pairing instructions do not appear.

You need to ensure that the HID pairing instructions appear when the image starts on a client computer that has neither a keyboard nor a mouse connected.

Which file should you create?

  1. unattend.xml

  2. Oobe.xml

  3. Coconfig.xml

  4. Sysprep.inf

Answer: B

Question No: 33

You start a computer namedComputer1from Windows Preinstallation Environment

(Windows PE).

You discover that you cannot access the network because the driver for the network card is not included in Windows PE.

You obtain a valid network driver forComputer1.

You need to ensure that you can access the network fromComputer1immediately. What should you do?

  1. Run dism.exe and specify the /Add-Driver parameter and the INF file of the driver.

  2. Run pnputil.exe and specify the -a parameter and the folder where the driver is located.

  3. Run drvload.exe and specify the INF file of the driver.

  4. Run wpeutil.exe and specify the InitializeNetwork parameter and the folder where the driver is located.

Answer: C

Question No: 34

You use Windows Deployment Services (WDS) to deploy Windows operating system images.

You create a custom image of Windows Preinstallation Environment (Windows PE).

You need to ensure that client computers use Pre-Boot Execution Environment (PXE) to load the Windows PE image.

To which node in the Windows Deployment Services console should you add the image?

  1. Install Images

  2. Multicast Transmissions

  3. Boot Images

  4. Pending Devices

  5. Legacy Images

Answer: C

Question No: 35

You work for an OEM system builder.

You deploy Windows 8 to a client computer that has a 64 GB-Solid State Drive (SSD) by using a configuration set from a USB key.

You need to reduce the size of the Windows installation as much as possible. Which folder should you remove from the installation?

  1. %WINDIR%\Panther

  2. %WINDIR%\Addins

  3. %WINDIR%\Configsetroot

  4. %WINDIR%\Branding

Answer: C

Question No: 36 DRAG DROP

Your network contains an Active Directory domain named contoso.com and a DHCP server named DHCP1.

You have a technician computer that has the Windows Assessment and Deployment Kit (Windows ADK) installed.

You prepare a reference computer namedComputer1.

You install Windows Deployment Services (WDS) on a server namedServer1. You need to capture an image ofComputer1and store the image onServer1.

Which three actions should you perform in sequence? (To answer, move the appropriate three actions from the list of actions to the answer area and arrange them in the correct order.)

Ensurepass 2018 PDF and VCE

Answer:

Ensurepass 2018 PDF and VCE

Explanation:

Box 1:Create a capture image.

Box 2:Start Computer1 by using Pre-Boot Execution Environment (PXE). Box 3:Add an install image to WDS.

Note:

Box 1: A capture image is created from an existing boot image. You will create a new capture image by right-clicking on an existing boot image and then selecting Create Capture Image option. The Create Capture Image Wizard will start.

Box 2:How to Create An Image by Using a Capture Image

Power up the reference machine and boot it up on the network. Choose the capture boot image when the PXE client starts.

Box 3:

The boot image will download over the network and start. A wizard starts. Later in the Wizard:

Ensurepass 2018 PDF and VCE

Question No: 37

You need to prepare a hard disk for a Unified Extensible Firmware Interface (UEFI)-based computer.

Which three actions should you perform? (Each correct answer presents part of the solution. Choose three.)

  1. Covert the hard disk to a GPT disk.

  2. Format the Windows partition by using NTFS.

  3. Format the Windows partition by using FAT32.

  4. Create an EFI partition.

  5. Mark the system partition as active.

Answer: A,B,D

Explanation: A:The GUID Partition Table (GPT) was introduced as part of the Unified Extensible Firmware Interface (UEFI) initiative. GPT provides a more flexible mechanism for partitioning disks than the older Master Boot Record (MBR) partitioning scheme that was common to PCs.

B: NTFS is the best choice for the Windows partition.

D:The EFI System partition is formatted using the FAT12, FAT16 or FAT32 file system.

Question No: 38

You are an OEM system builder.

You are customizing the OEM support information for Windows 8. You set HelpCustomized to true.

You need to identify where the customized support information will appear. What should you identify?

  1. System in Control Panel

  2. Windows Help and Support

  3. The Windows Welcome screen

  4. Troubleshooting in Control Panel

Answer: B

Question No: 39

You have three images sealed in Out-of-Box-Experience (OOBE) mode. You use the images on a daily basis to build client computers for customers.

A new customer places an order for 500 computers. The customer#39;s requirements for the computers are not met by any of the images.

You identify an image that you can modify by installing two applications required by the customer.

You plan to customize the image before you deploy the image to the computers. You need to identify which steps must be taken to modify the image.

What should you do before you capture the image?

  1. Start the image in audit mode on a reference computer. Install the required applications. Seal the image in audit mode.

  2. Start the image in audit mode on a reference computer. Install the required applications. Seal the image in OOBE mode.

  3. Start the image in audit mode on a reference computer. Install the required applications. Restart the computer.

  4. Start the image on a reference computer. Install the required applications. Seal the image in audit mode.

Answer: B

Question No: 40

You are creating a Windows 8 answer file.

You need to modify the order in which the app tiles appear on the Start screen.

Which component should you add to the answer file?

  1. Microsoft-Windows-Deployment

  2. Microsoft-Windows-Setup

  3. Microsoft-Windows-SharedAccess

  4. Microsoft-Windows-Shell-Setup

Answer: D

100% Ensurepass Free Download!
Download Free Demo:74-697 Demo PDF
100% Ensurepass Free Guaranteed!
Download 2018 EnsurePass 74-697 Full Exam PDF and VCE

EnsurePass ExamCollection Testking
Lowest Price Guarantee Yes No No
Up-to-Dated Yes No No
Real Questions Yes No No
Explanation Yes No No
PDF VCE Yes No No
Free VCE Simulator Yes No No
Instant Download Yes No No
         

You must be logged in to post a comment.

Proudly powered by WordPress   Premium Style Theme by www.gopiplus.com